Browse all practice questions for the Beechjet 400A Computer Training Systems (CTSys) Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Beechjet 400A Computer Training Systems (CTSys) Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • During an aborted takeoff, if engine fire indications exist, should you deploy the reverser on the affected engine?
  • If after corrective action the reverser will not stow and UNLOCK/DEPLOY annunciators and EMER STOW are illuminated, the crew should move the thrust lever to which position?
  • Which condition triggers the emergency pressurization valve to open?
  • A hydraulic pressure reading of 1850 psi would be indicated on the hydraulic pressure gauge at the:
  • Under icing conditions, if icing is encountered for more than 10 minutes after selecting 10-degree flaps, should you land with 10-degree flaps?
  • The mistrim warning horn will sound during takeoff if pitch trim is not within the takeoff range.
  • The Beechjet 400A fuel storage system consists of which tanks?
  • If the airplane is equipped with a battery temperature light and the temperature continues to rise and reaches 150 degrees F, the crew should:
  • Which statement about elevator trim tabs is true?
  • What is the first pilot action if experiencing an engine failure above V1 during a takeoff?
  • If the speedbrakes are extended and you need to retract them, which procedure should you use?
  • The maximum generator load limit before attempting a generator assisted start is
  • Which combination constitutes proper normal operation of the inverter and its control in the AC electrical system?
  • Autopilot operation: which statement is true?
  • The landing gear warning horn sounds when the gear is retracted and:
  • If the EMER BUS FDR FAIL annunciator comes on, the emergency relay opens and the emergency bus receives power from which bus?
  • What is the minimum voltage required to attempt a battery start?
  • The aft filler tank is located in which part of the aircraft?
  • When the EMER BRAKE handle is pulled, how many brake applications can the air bottle provide?
  • Which statement is true about manual cabin pressure control?
  • Which of the following is the correct value for the maximum N1 redline?
  • When the L or R F FLTR BYPASS annunciator indicates a clogged filter, what is the recommended crew action?
  • If the FLAP ASYM light illuminates, the flaps can be moved from the position where asymmetry occurred.
  • In a pitch trim runaway, the initial action is to:
  • The maximum N1 at transient is:
  • FMS navigation data base updates must be loaded each:
  • Pressure above 53 PSIG or temperature above 400 F will close both pressure-regulator and shutoff valves, and open the emergency pressurization valve. Which values are these thresholds?
  • The Beechjet 400A's maximum differential pressure is:
  • During cruise flight, the electrical boost pump switches should be selected:
  • If operation of the vent blower fan is desired prior to starting engines, how long must you wait after turning off the vent blower before opening the cabin door or emergency exit?
  • The cabin pressure controller provides the crew with a means to control the pressurization system.
  • If the same brand of oil is not available for replenishment, Synthetic Oil Type II may be added provided the total quantity added does not exceed
  • If you cannot isolate the electrical fire source and both generators are switched to EMER, what should the crew do?
  • When operating above 41,000 ft with both generators operating, current is limited to per generator
  • If the LH engine fire light remains on after moving the thrust lever to IDLE, which sequence should the pilot perform?
  • The maximum fuel temperature is:
  • What is the first crew action in response to an electrical fire or smoke?
  • What is the primary purpose of engine synchronization?
  • If a one engine inoperative approach and landing is conducted with a reverser deployed, how does landing distance change?
  • What is the first action the crew should take in an emergency descent?
  • What is the static thrust of the JT15D-5 engine on a standard day at sea level?
  • If a thrust reverser ARM annunciator remains illuminated in flight after corrective actions, what should the crew do?
  • An adjustable gust lock immobilizes the elevators when attached to the what?
  • If the crew notes RPM decay, slower acceleration and increased travel for a given power setting, this indicates which subsystem failure is most likely?
  • How many filler ports are used for refueling Beechjet 400A?
  • The JT15D-5 engine starting limit when ITT is 550 to 600 degrees C is a maximum of:
  • Which gauge has a yellow arc indicating 1200 to 1350 psi?
  • During engine start, move the thrust lever to IDLE when N2 reaches what percent?
  • When should fuel crossfeed occur?
  • Which of the following is NOT a marked thrust lever position?
  • The L or R ENG ICE TEMP LO caution light indicates engine inlet bleed air temperature is:
  • What color is the indicator light that shows the electric boost pump is operating?
  • If the LH engine fire ON light illuminates and the fire bell audible warning sounds, the pilot should first do what?
  • The fuel system is designed to operate between sea level and how many feet, with a temperature range from -40 °C to what °C?
  • How many positions does the AC voltage selector switch have?
  • Ignition switches on the Beechjet 400A are which type?
  • Which four positions are marked on the engine thrust levers?
  • What is the effect of placing the battery switch in the EMER position?
  • Before opening the cabin door after turning off the vent blower, how long must the vent blower be off?
  • If the GEN OFF light illuminates and cannot be reset, the operating generator N2 should be:
  • During icing approach, after selecting 10 degrees flaps, wait how many seconds before selecting 30 degrees flaps?
  • Flight in visible moisture without pitot heat may result in erratic operation of which instruments?
  • If the oil pressure is 50 PSI and the OIL PRESS LO light does not illuminate, the pilot should:
  • The exhaust section delivers thrust by what mechanism?
  • A GPU start is recommended at ambient temperature below approximately minus 15 degrees C with a DC voltage minimum of how many volts?
  • Which statement about battery feeder fail light is true?
  • The windshield anti/deice switch to HI mode is prohibited during which phase?
  • What is the maximum tailwind component allowed for landing?
  • In an engine failure during landing configuration, what is the recommended action regarding thrust?
  • A rotating-disc-type assembly in each main gear provides:
  • Which tank feeds the left engine during normal operation?
  • Which statement correctly describes the role of the primary power distribution system?
  • If the FIRE DET FAIL annunciator illuminates following an ENG FIRE PUSH switch illumination, the fire should be considered to be:
  • The Beechjet 400A is approved to operate up to:
  • If the battery temperature reaches 150°F and does not decrease after turning the battery OFF, what is the recommended action?
  • What is the recommended action if the battery temperature does not decrease after switching OFF, according to the procedure?
  • Which component limits cabin altitude to approximately 12,500 +/- 1,500 feet?
  • The aft baggage load limit is less than the maximum landing weight. Which statement is true?
  • The cabin pressurization controller can vary cabin altitude from which range?
  • If the right load bus loses power and No.1 inverter has also failed, from which source does No.2 inverter receive power?
  • Which statement is true regarding in flight operation of the ice protection systems?
  • If FUEL XFEED is set to L TANK, the left tank fuel is available to which engines?
  • What is the rating of each Beechjet 400A generator?
  • What is the usable fuel capacity of the Beechjet 400A?
  • The heating system protects which items?
  • What is the red line maximum on the ammeter for RK1 through RK97 not modified by one of the appropriate kits?
  • If the L FUEL PRESS LO annunciator illuminates, the correct crew action is:
  • When selecting the right generator on the DC voltage selector switch, which position is used?
  • Environmental system smoke or odor: after the crew dons oxygen masks and selects Mic to OXY MASK, the next action is to isolate the cabin pressure source by selecting L ENG or R ENG.
  • Per engine oil replenishment limit per 400 hours
  • How many airstarts are permitted when an engine has been shut down due to obvious mechanical difficulties?
  • What energy source powers the wing leading-edge anti-icing system?
  • What do control column shaking and an angle-of-attack display on cockpit indicators warn you of?
  • The ON position of the fuel transfer pump switch is used:
  • What is the status of the NOSE and RH gear lights when the left gear is unlocked?
  • During takeoff, the CABIN PRESS LO light may be illuminated at airports above which elevation?
  • To start the right engine, the crew should first perform which action?
  • The MAN PRESS CONT valve is located on which panel?
  • If the speedbrakes fail in the extended position, EMER RET retracts.
  • Oil pressure warning light illuminates when oil pressure falls below what value?
  • At what altitude is the VMO specified as 320 KIAS?
  • During smoke removal procedures in flight, to what altitude should the aircraft descend?
  • Which indicator shows the left gear is not locked when the gear handle is down?
  • Which statement describes the low-pressure turbine in the JT15D engine?
  • Which option completes the LH engine fire sequence after the initial step of moving the thrust lever to IDLE if the LH engine fire light remains on?
  • What does the NORM T.O. marking on the thrust lever indicate?
  • During approach in icing conditions, wait at least how many seconds after selecting 10 degrees flaps before selecting 30 degrees flaps?
  • Maximum takeoff weight is described as being limited by
  • On which panel does the L or R OIL PRESS LO warning light appear?
  • The engine anti-ice system requires the engine anti-ice switch to be ON to regulate bleed air pressure to 16 PSI. True or False?
  • During takeoff, if an inadvertent thrust reverser deployment occurs below V1, what is the first pilot action?
  • Under icing conditions indicated by the ICING annunciator or airframe ice accumulation, the anti-ice system should be used at ram air temperatures of:
  • The maximum differential pressure is:
  • The VMO airspeed limit at 19,000 feet is 320 KIAS.
  • What is the maximum wing tank imbalance allowed for takeoff in the Beechjet 400A?
  • The cabin press LO light may illuminate during takeoff at airports above what elevation?
  • When the electric boost pump is operating, the crew is informed by means of:
  • The maximum wing tank imbalance for takeoff is 100 pounds. Which of the following reflects that?
  • During normal operation, which buses are powered by No.1 inverter?
  • The red line on the oxygen pressure gauge indicates a pressure of what value?
  • Which annunciator indicates wing tank overpressure?
  • The L FUEL LEVEL LO annunciator corresponds to fuel quantity in which tank?
  • Engine anti-ice systems must be on for taxi and takeoff when in visible moisture at what temperature?
  • Which statement best describes the Beechjet 400A fuel system's per-engine fuel supply?
  • The minimum oil temperature for starting is:
  • If the LH engine fire light remains on after moving the thrust lever to IDLE, which action should be performed next?
  • In turbulent air penetration, what airspeed should be maintained?
  • For an approach climb on a one-engine go-around, what is the designated initial flap setting?
  • To have pressure regulator shutoff valve open and regulate bleed air pressure for engine anti-ice at 16 PSI, engine anti-ice switch must be in which position?
  • When the trim interrupt switch is pushed, the autopilot is disengaged and:
  • If the landing gear handle is down but the left gear does not lock, which indicator configuration is shown?
  • What is the maximum operating altitude?
  • Which statement about the Beechjet 400A is true?
  • For a GPU start at ambient temperatures below approximately -15 C, the DC voltage minimum should be what value?
  • The nonessential buses are protected by what type of device on the main circuit breaker panel?
  • Igniters are located in which engine section?
  • If stabilizer ice is suspected and the anti-ice/deice switches are off, what is the recommended flap limit?
  • No-flap approach and landing will cause landing distance to
  • The temperature control system for air conditioning is operated by which power source?
  • As the spoilers on one wing extend, what do the spoilers on the other wing do?
  • Which statement about Synthetic Type II replenishment is true?
  • Which pair of buses are connected by the LH BUS TIE RCCB to allow power routing?
  • The function of the altitude pressure regulator is to limit cabin altitude to what value range?
  • The Pratt & Whitney JT15D-5 turbofan engine operating limit for engine start if the ITT is 550 to 600 degrees C is a maximum of:
  • In non-icing conditions, the anti-ice system should be used only at ram air temperatures of:
  • Which light indicates aft fuselage tank depletion?
  • Describe the DC voltage selector switch.
  • During emergency braking, is it advisable to use the normal braking system for optimal braking power?
  • The ITT gauge yellow arc indicates temperatures between which range?
  • The load limit for the aft cabin baggage compartment is
  • For ditching, what is the flap setting during the approach?
  • If wing tank overpressure occurs and the respective transfer switch is in AUTO, what happens to the transfer pump?
  • The L FUEL LEVEL LO annunciator indicates approximately how much fuel remains in the left tank?
  • The fuel transfer switches are three position switches labeled:
  • Which statement about takeoff and fuel configuration is true?
  • How many stages are in the low compressor section of the JT15D engine?
  • The high compressor section of the JT15D engine consists of which component?
  • To disconnect the LH Main bus from the battery charge bus, pull the:
  • In the event of a jet pump failure, what action should the crew take for the affected engine?
  • If the thrust reverser ARM annunciator remains illuminated after corrective actions, what is the recommended course of action?
  • Above 60% N2, the normal engine oil pressure is within which PSIG range?
  • The statement 'In turbulence, maintain 200 KIAS' is true.
  • Autopilot disengagement will initiate an aural tone. The tone can be cancelled by a second actuation of the:
  • The windshield heat guidance for flight is:
  • What is the maximum redline N1 percentage?
  • Which component is responsible for producing thrust by mixing bypass air with core exhaust?
  • Unless icing conditions are indicated by the ICING annunciator or airframe ice accumulation, at ram air temperatures above what value should anti/deice systems not be operated?
  • The maximum landing weight is
  • Rudder boost must be operable and:
  • During takeoff, thrust setting must be attained by which indicated airspeed?
  • With the electric boost pumps in Auto, the crew can expect the respective pump to operate:
  • What is the probable cause for a flashing master warning after gear retraction?
  • When FLOOR/DEFOG is set to DEFOG, defog air is directed to which area?
  • During an inadvertent overspeed, which phrase may be used to establish crew communication?
  • What does the AUTO position do for the fuel transfer pump?
  • In the event of a loss of both generators, the crew's first step is to:
  • In a false start, what is the first action you should take?
  • If UNLOCK/DEPLOY annunciator and EMER STOW illuminated after thrust reverser deployment, what does this indicate?
  • The maximum time for continuous reverse thrust above reverse idle is?
  • Where is the indicator for electric boost pump operation located?
  • How is the turbine section of the JT15D engine described?
  • Where is the standby power system mounted?
  • In the event of high engine oil temperature, what procedure should the crew follow?
  • Which sequence correctly describes the left fuel system action when the L FUEL PRESS LO annunciator is lit?
  • Which statement correctly matches the JT15D-5 engine’s thrust values on a standard day?
  • With flaps at 0 degrees, what are the maneuvering load factors?
  • During a false start, what is the correct sequence of actions to purge fuel and attempt a restart?
  • Under normal operation, which statement is true about the inverter control settings?
  • The correct type of oil for the Beechjet 400A engines is
  • Which unit is used for weight on the Beechjet 400A?
  • Which statement about cooling the engine oil is true?
  • When does the L or R OIL PRESS LO warning light illuminate?
  • How many mid fuselage tanks are in the fuel storage system?
  • In the event of pitch trim runaway, the crew's first action should be:
  • Which of the following represents the proper switch positions for normal operation of the AC electrical system?
  • Which indicator illuminates to indicate inadvertent thrust reverser deployment in flight?
  • Inadvertent overspeed, the crew should first:
  • Which condition allows anti-ice operation above 10 °C?
  • If the engine does not light off within 10 seconds during start, which sequence should be followed?
  • Engine oil is cooled by means of which device?
  • If gear is raised after takeoff with a flashing master warning and thrust reverser ARM annunciators, what is the probable cause?
  • The minimum oil pressure at idle when N2 is below 60% is which PSIG?
  • For an approach with one engine go-around, what initial flap setting should be used?
  • The white light above the wing deice switch illuminates when the wing temperature sensor senses approximately what temperature?
  • When testing the stall warning system before starting the engines, the master test switch must remain in which position until the column shaker and stall annunciator lights/horn actuate twice?
  • When the right load bus loses power and No.1 inverter has failed, No.2 inverter is powered from which bus?
  • Which power distribution system provides the connection between the main buses and the respective load buses?
  • In the Beechjet 400A, a jammed stabilizer in a nose-down position requires following normal landing procedures.
  • Which caution light indicates engine inlet bleed air temperature is too low?
  • During normal operation, to what position should the Inverter selector switch be set?
  • For Beechjet 400A, the maximum allowable fuel unbalance for landing is:
  • The maximum N2 for takeoff is:
  • With speed brakes extended in flight, which statements are true?
  • What is the maximum fan RPM (N1) percentage?
  • Nav captures with the autopilot must have an intercept angle of:
  • How long should crew wait before attempting a second external power assisted start after the first start attempt fails?
  • If No.1 inverter fails, what does No.2 inverter do?
  • Which are not buses in the secondary power system?
  • What does the engine fire detector test switch enable the crew to check?
  • If No.1 inverter fails and No.2 inverter takes over, what happens to the secondary buses?
  • Which of the following is/are protected by a heating system?
  • Normally, from which source is the No.2 inverter powered?
  • Which of the following sequences correctly describes the overspeed recovery steps?
  • In an inadvertent icing encounter, turning wing anti-ice ON with significant wing ice accumulation could result in engine ice ingestion.
  • Refueling of the Beechjet 400A is accomplished through?
  • The DC electrical power distribution system has four subsystems. Besides power source distribution and primary power distribution, which are the other two?
  • Maximum takeoff weight for the Beechjet 400A is
  • Which valve provides manual cabin pressure control?
  • Which action completes the LH engine fire procedure after initial steps?
  • Which component is used to increase bleed air flow through the venturi of the ACM?
  • What is the minimum voltage allowable for a battery start?
  • Which is true regarding the autopilot?
  • Which condition will illuminate the L or R FUEL LEVEL LO lights?
  • The quick dump valve, located on the bottom left edge of the right instrument panel provides a means for rapid and complete cabin depressurization.
  • Where is the wing leading-edge anti-icing switch located?
  • Regarding the EFIS, which statement must be true for takeoff?
  • The ambient air temperature limitation for landings is:
  • When the STAB anti ice control switch is turned on, the system's light will:
  • Should the pilot attempt to use the normal pitch trim system after pitch trim runaway?
  • What would the thermal discharge indicator on the aft left fuselage show if one or more fire bottles had been discharged?
  • When using the autopilot, nav captures, including localizer captures, must be accomplished with an intercept angle of:
  • Which statement best describes nose wheel steering?
  • In OEI conditions with a reverser deployed, the landing distance is expected to increase by about what percentage?
  • The maximum ITT temperature for continuous operation is:
  • What is the purpose of the water separator of the air cycle machine?
  • The refrigeration air conditioning OFF for Takeoff and Landing.
  • What is the biggest hazard of turning on wing anti-ice when ice is on wings?
  • Which inverter is responsible for powering the primary buses when No.1 inverter fails?
  • If external power is used to start the aircraft, what should the battery switch be?
  • The ambient temperature range for landings spans from:
  • When landing with ice accumulation on the wings, what is the recommended airspeed after final flap extension?
  • In case of failure of the horizontal stabilizer anti-ice or deice system, with both switches off and ice suspected, the maximum flap deflection is limited to:
  • Illumination of the L or R WG TK OV PRESS annunciator indicates pressure in the wing tank in excess of 3.5 psid and also causes:
  • How many forward fuselage tanks does the fuel storage system include?
  • Fuel flow to the engine is controlled by which system?
  • How many fuel tanks are in the Beechjet 400A fuel storage system?
  • If a landing must be made with a jammed rudder, the guidance indicates that:
  • The yellow arc of the Nitrogen pressure gauge indicates a range of:
  • In a power brake failure, the pilot will break the safety wire and remove the guard clip on the emer brake handle, then pull that handle. Approximately how many applications are available with a full system?
  • What is the maximum continuous thrust of the JT15D-5 engine?
  • During stall warning system testing, the master test switch must remain in which position until the column shaker and stall annunciator lights/horn actuate twice?
  • Which statement is true regarding the engine compartment fire extinguishing system?
  • The thrust reversers can be deployed under which conditions?
  • FMS navigation data base updates must be loaded at the end of which period?
  • Which option states manual cabin pressure control using the MAN PRESS CONT valve?
  • A flow increase valve operates to increase the volume of bleed air flowing through the venturi of the ACM when the engine thrust lever is set:
  • What is the minimum duration the standby power system can supply emergency power?
  • Which annunciator indicates a clogged fuel filter?
  • The takeoff mistrim warning horn will sound when thrust levers are advanced to takeoff position if the pitch trim is not in the takeoff range.
  • If the yaw damper fails in flight and cannot be re-engaged, the flight may be continued below 28,000 feet.
  • What is the maximum fuel temperature value in degrees Celsius?
  • What type and labeling do the generator master switches have?
  • The maximum fuel imbalance permitted for landing is:
  • The maximum continuous ITT temperature is:
  • Selecting the FUEL XFEED L TANK switch allows fuel from the left tank to supply which engines?
  • What maximum airspeed should be maintained after cutoff due to inadvertent reverser not stowing?
  • What is the maximum engine oil temperature specified for the Beechjet 400A?
  • The windshield heat must be used during flight under which condition?
  • Which subsystem carries the load to the electrical loads?
  • An engine synchronization system automatically synchronizes the engines to reduce noise level and enhance passenger comfort.
  • If the RH load bus DC power fails, what happens to the No.2 Inverter relay?
  • The anti-ice system on the Beechjet 400A should be used at ram air temperatures of at most what, unless icing conditions are indicated?
  • Do the elevators have trim tabs?
  • The L or R FUEL TRANS PRESS LO light indicates that:
  • Maximum takeoff weight is limited by
  • If cabin altitude cannot be corrected and exceeds 14,000 feet, what procedure should be initiated?
  • On the ground with gear down and anti-skid ON, anti-skid protection is active under which condition?
  • If the engine does not light off within 10 seconds during start, which action should be taken?
  • Which option correctly represents the normal oil pressure range above 60% N2?
  • During overspeed, if the aircraft is nose down, what action should be taken?
  • When performing a one engine inoperative approach and landing, when should the flaps be set to 30 degrees?
  • With flaps at 0 degrees, the maneuvering load factors are within the range of:
  • During hydraulic operation, which color band on the hydraulic pressure gauge indicates 1850 psi?
  • What is the total usable fuel in the Beechjet 400A?
  • When conditioned or emergency air is no longer being supplied, ventilation is supplied from which source?
  • All generator power is distributed through which components?
  • Which of the following is true about the Beechjet 400A's fuel system configuration?
  • The aural tone that sounds when the autopilot disengages can be cancelled by a second actuation of which control(s)?
  • The primary power distribution system consists of the left main bus and:
  • If electrical fire results in switching both master generator switches to EMER, which systems will not be available?
  • In a false start, after purging fuel for 15 seconds, what action should follow?
  • Which statement accurately describes the relationship between the cabin pressure controller and the altitude regulator?
  • If the CABIN PRESS LO light illuminates and cabin decompression is not rapid, when should emergency descent procedures be initiated?
  • Which annunciator action occurs when EMER BUS FAIL is indicated?
  • For a jammed spoiler, the indicated approach speed should be VREF + 10 KIAS.
  • Which statement best describes when the battery feeder fail light will illuminate?
  • Each Beechjet 400A generator is rated at:
  • The ram air duct includes a check valve to provide ventilation when conditioned air is unavailable.
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy